![]() ![]() You should make sure that you are applying enough pressure so that the blade cuts through the vinyl lattice. Then, you will need to apply pressure to the utility knife and run it along the straight edge. To do this, you will need to hold the utility knife at a 90-degree angle to the straight edge and make sure that the blade is in contact with the straight edge. Next, you will need to score the vinyl lattice with the utility knife. If you do not have either of these, you can use a piece of string or twine. A utility knife is a tool that is used for many purposes, including cutting vinyl lattice.įirst, you will need to find a straight edge to use as a guide. ![]() To cut vinyl lattice, you will need a utility knife. If you don’t have a circular saw, you can use a hand saw or jigsaw, but these may take longer to cut through the material. ![]() Be sure to wear safety goggles when operating the saw. If you are working with a large piece of lattice, it may be easier to use a ladder so you can reach the top of the panel easily.ģ.Cut along the line you drew using a circular saw with a fine-toothed blade. Make sure the line is straight by using a level as a guide. Write down your measurements so you can refer to them later.Ģ.Draw a line on the back of the lattice panel using a pencil where you will need to make your cut. Use a tape measure to determine the length and width of the space. Cutting vinyl lattice panels how to#With a few tools and some easy-to-follow instructions, you can learn how to cut vinyl lattice in no time!ġ.Measure the area where you will be installing the lattice. Cutting vinyl lattice panels install#When you’re ready to install your lattice, you’ll need to know how to cut it to fit your space. It’s available in wood or vinyl and comes in a variety of styles. Lattice is a versatile product that can be used for a variety of projects in your home, including hiding unsightly areas, creating privacy or adding decorative accents. A pencil mark will give you a guide to follow when cutting, and it will be easy to erase if you make a mistake. Use a pencil to lightly mark the vinyl lattice where you want to make your cuts. Once you have made your cut, remove any sharp edges or burrs from the cut edge of the vinyl lattice using a file or sandpaper. If you are using a knife, be sure to use a cutting board or other surface to protect your work surface. Next, using a sharp knife or a pair of scissors, carefully cut along the marked line. Make sure that the mark is straight and even. Then, using a tape measure, mark the point where you will need to make your cut. A partner can help to support the panel for you as you cut, which will make your job easier.You will need the following materials to cut vinyl lattice: a straight edge, a utility knife, a measuring tape, and a pencil.įirst, measure the area where you will be cutting the vinyl lattice. The panels must be supported along both sides if you want to cut neatly and safely. It helps to have somebody to help you as you cut. If not held down firmly, the lattice can split or tear. As you approach the end of a cut, be sure to support the panel firmly, especially at the cut line. Cut at a steady pace so the material doesn’t chip or crack. However, the “back” side should be up when a rotary saw is in use. Cut Correctlyīe sure the lattice “face” side is upward when a fine-toothed hard saw is in use. If you plan to make angled or curved cuts, use a power-saber saw. To cut vinyl lattice, attach a vinyl-cutting blade to the power saw. It also enables you to cut accurately and effectively. This will enable you to cut through the staples in the panels with ease. ![]() It is best to attach a carbide-tipped wood blade to the power saw for a wooden lattice. Use a power saw such as a circular saw or fine-toothed hard saw to cut the panels to size. Removing these staples first will reduce the risk for flying bits of staple when you cut the lattice. Try and remove as many of the staples as you can that are along the cut line. These grid panels have many staples that help to secure the lattice in place. Use a chalk line to indicate the cut line. Alternatively, cut the panels with a few inches of allowance that can extend into the ground. For installation on slopes, you must cut the panels to correspond with the grade. Allow an additional 1/4 inch on all sides of the panel to accommodate expansion and contraction. If the area to be framed isn’t square, it will be necessary to make extra cuts to enable the panels to fit properly. Doing so will ensure the panels fit properly into the framing and support posts. It is important to take accurate measurements of your project, especially the width. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |